Turns off the output when the operation switches from constant voltage mode to constant current mode or vice versa. Can be set as necessary.
Overvoltage protection (OVP)
Inverter shutoff system. Prevents the output voltage from being set higher than the OVP value. Also shuts off the output when an output overvoltage (exceeding the OVP value) occurs.
Overvoltage protection voltage setting range
0.5 V to 12 V
1 V to 24 V
2 V to 40 V
5 V to 66 V
5 V to 110 V
5 V to 176 V
5 V to 353 V
5 V to 717 V
Undervoltage limit (UVL)
Prevents the output voltage from being set lower than the UVL value. Disabled during external control.
Undervoltage protection (UVP)
Shuts off the output when the output voltage falls below the UVP value.
Overheat protection
Shuts off the output before the temperature of the internal components exceeds the safe operation temperature.
Item/Model
PAV10-20
PAV20-10
PAV36-6
PAV60-3.5
PAV100-2
PAV160-1.3
PAV320-0.65
PAV650-0.32
Foldback protection
Turns off the output when the operation switches from constant voltage mode to constant current mode or vice versa. Can be set as necessary.
Overvoltage protection (OVP)
Inverter shutoff system. Prevents the output voltage from being set higher than the OVP value. Also shuts off the output when an output overvoltage (exceeding the OVP value) occurs.
Overvoltage protection voltage setting range
0.5 V to 12 V
1 V to 24 V
2 V to 40 V
5 V to 66 V
5 V to 110 V
5 V to 176 V
5 V to 353 V
5 V to 717 V
Undervoltage limit (UVL)
Prevents the output voltage from being set lower than the UVL value. Disabled during external control.
Undervoltage protection (UVP)
Shuts off the output when the output voltage falls below the UVP value.
Overheat protection
Shuts off the output before the temperature of the internal components exceeds the safe operation temperature.
Setting and readback (USB, RS232, RS485, optional LAN interface)
Separate knobs (encoders) for setting the output voltage and output current (setting resolution switchable).
Knobs (encoders) for setting OVP,UVP,and UVL.
Protection functions (OVP, UVP, UVL, foldback)
Output shutoff function (output on/off control, shutdown)
Communication functions: Standard equipped with USB, RS232, RS485. LAN optional.
Baudrate, address setting
External control: Configuration using external voltage (5 V or 10 V) or external resistance (5 kΩ or 10 kΩ), output voltage/current monitor output (5 V or 10 V), output on/off, front panel operation lock
Output voltage display
Accuracy
0.5% of the rated output voltage ± 1 count
Number of decimal digits
2 digits
1 digit
Output current display
Accuracy
0.5% of the rated output current ± 1 count
Number of decimal digits
2 digits
3 digits
LED display
Green: FINE, MENU, SET, ALARM, REM, OUTPUT, CV, CC
Red: ALARM (OVP, UVP, OTP, FOLD, AC FAIL)
Setting keys
FINE, MENU, SET, ALARM, REM, OUTPUT
Item/Model
PAV10-20
PAV20-10
PAV36-6
PAV60-3.5
PAV100-2
PAV160-1.3
PAV320-0.65
PAV650-0.32
Control function
Separate knobs (encoders) for setting the output voltage and output current (setting resolution switchable).
Knobs (encoders) for setting OVP,UVP,and UVL.
Protection functions (OVP, UVP, UVL, foldback)
Output shutoff function (output on/off control, shutdown)
Communication functions: Standard equipped with USB, RS232, RS485. LAN optional.
Baudrate, address setting
External control: Configuration using external voltage (5 V or 10 V) or external resistance (5 kΩ or 10 kΩ), output voltage/current monitor output (5 V or 10 V), output on/off, front panel operation lock
Output voltage display
Accuracy
0.5% of the rated output voltage ± 1 count
Number of decimal digits
2 digits
1 digit
Output current display
Accuracy
0.5% of the rated output current ± 1 count
Number of decimal digits
2 digits
3 digits
LED display
Green: FINE, MENU, SET, ALARM, REM, OUTPUT, CV, CC
Red: ALARM (OVP, UVP, OTP, FOLD, AC FAIL)
Setting keys
FINE, MENU, SET, ALARM, REM, OUTPUT
*1. The minimum voltage is 0.1 % of the rated output voltage. *2. The minimum current is 0.2 % of the rated output current. *3. Input voltage 100 Vac/200 Vac, at the rated output power, ambient temperature 25 °C If the LAN option is built in, the efficiency decreases by 0.5 % and the input current increases by 0.5 %. *4. Excludes input surge current (duration 0.2 ms or less) applied to the built-in noise filter section. *5. 85 Vac to 132 Vac or 170 Vac to 265 Vac, fixed load *6. With the input voltage held constant, the sensing point was measured using remote sensing from no load to full load. *7. Models with rated output voltages from 10 V to 100 V were measured using an RC- 9131 A 1:1 probe that conforms to the JEITA specifications. Models with rated output voltage from 160 V to 650 V were measured using a 10:1 probe. *8. When at least 8 hours has passed after a 30 minute warm-up with the input voltage, load, and ambient temperature held constant *9. For 30 minutes after turning on the power with the input voltage, load, and ambient temperature held constant *10. Between 10 % and 90 % of the rated resistive load and rated output voltage *11. If the output voltage is repeatedly decreased, Td is the minimum duration from a given voltage drop to the next voltage drop. *12. Duration for the voltage to change from 90 % to 10 % of the rated output voltage when the output voltage is repeatedly decreased and the duration from a given voltage drop to the next voltage drop is longer than Td. *13. Duration for the voltage to change from 90 % to 10 % of the rated output voltage when the output voltage is repeatedly decreased and the duration from a given voltage drop to the next voltage drop is shorter than Td. *14. The amount of time required for the output voltage to return to a value within 0.5 % of the rated output voltage. The change in the load current is 10 % to 90 % of the rating. The output voltage is between 10 % and 100 % of the rating. During local sensing. *15. At the rated output power *16. The value when the output voltage is changed from the lower limit to the rated voltage in constant current mode with the input voltage held constant *17. For models with a 10 V rated output voltage, this is the value for when the output voltage is 2 V to 10 V at the rated output current. For other models, this is the value for when the output voltage is 10 % to 100 % of the rating at the rated output current. Models with rated output voltage from 160 V to 650 V were measured using a 10:1 probe. *18. In output current control, the current, linearity, and monitor accuracies do not include the load variation caused by initial drift and temperature drift of internal components.
0% to 100% of the rated output voltage (application voltage range selectable: 0 V to 5 V or 0 V to 10 V) Accuracy and linearity: ± 0.5% of the rated output voltage
Output current control using external voltage *1
0% to 100% of the rated output current (application voltage range selectable: 0 V to 5 V or 0 V to 10 V) Accuracy and linearity: ± 1% of the rated output current
Output voltage control using external resistance
0% to 100% of the rated output voltage (application resistance range selectable: 0 Ω to 5 kΩ or 0 Ω to 10 kΩ) Accuracy and linearity: ± 1% of the rated output voltage
Output current control using external resistance *1
0% to 100% of the rated output current (application resistance range selectable: 0 Ω to 5 kΩ or 0 Ω to 10 kΩ) Accuracy and linearity: ± 1.5% of the rated output current
Output shutoff (SO) control
External voltage application: 0 V to 0.6 V, 4 V to 15 V, or a contact switch. Positive or negative logic selectable.
Output current monitor *1
Monitor voltage range selectable: 0 V to 5 V or 0 V to 10 V, Accuracy: 1%
Output voltage monitor
Monitor voltage range selectable: 0 V to 5 V or 0 V to 10 V, Accuracy: 1%
Normal operation status signal
Normal (4 V to 5 V), abnormal (0 V), output resistance 500 Ω
Parallel operation *2 *3
Possible up to six power supplies. Master-slave operation with a current balance function.
Series operation *4
Possible up to two power supplies.
Constant voltage/constant current mode (CV/CC) signal
Open collector output (maximum application voltage 30 V, maximum sink current 10 mA)
Low level (on) during constant current (CC) mode High level (off) during constant voltage (CV) mode
Output on / off control (ILC)
Output can be shut off using a contact switch or the like (maximum voltage between terminals: 5 V). When open: Output off When shorted: Output on
Local / remote
Can be switched by applying an external voltage or by opening or shorting the circuit.
Local: 2 V to 15 V or open Remote: 0 V to 0.6 V or shorted
External control status signal
Open collector output (maximum application voltage 30 V, maximum sink current 10 mA)
High level (off) during local mode Low level (on) during external control
Trigger output signal
Maximum low level output signal: 0.8 V
Minimum high level output signal: 3.8 V, maximum high level output signal: 5 V
Maximum source current: 16 mA, output trigger signal span: 20 μs (typ)
Trigger input signal
Maximum low level input signal: 1.2V
Minimum high level input signal: 3.5 V, maximum high level input signal: 5 V
Maximum sink current: 16 mA, positive edge trigger span: 10 μs (min)
Tr/Tf: 1 μs (max)
Program signal output 1
Open collector output (maximum application voltage 25 V, maximum sink current 100 mA)
Program signal output 2
*1. In output current control, the current, linearity, and monitor accuracies do not include the load variation caused by initial drift and temperature drift of internal components. *2. For parallel operation of two or more PAV series power supplies with the same rating, the minimum load current is 5% of the rating or higher. For parallel operation of four or less models with rated output voltage of 160 V to 650 V, the minimum load current is 5% of the rating or higher. For parallel operation of more than four, the minimum load current is 20% of the rating or higher. *3. The ammeter’s display accuracy when the total current is displayed on the master unit is 2% ± 1 count of the total of rated currents. *4. An external protection diode is necessary.
Output voltage control using external voltage
0% to 100% of the rated output voltage (application voltage range selectable: 0 V to 5 V or 0 V to 10 V) Accuracy and linearity: ± 0.5% of the rated output voltage
Output current control using external voltage *1
0% to 100% of the rated output current (application voltage range selectable: 0 V to 5 V or 0 V to 10 V) Accuracy and linearity: ± 1% of the rated output current
Output voltage control using external resistance
0% to 100% of the rated output voltage (application resistance range selectable: 0 Ω to 5 kΩ or 0 Ω to 10 kΩ) Accuracy and linearity: ± 1% of the rated output voltage
Output current control using external resistance *1
0% to 100% of the rated output current (application resistance range selectable: 0 Ω to 5 kΩ or 0 Ω to 10 kΩ) Accuracy and linearity: ± 1.5% of the rated output current
Output shutoff (SO) control
External voltage application: 0 V to 0.6 V, 4 V to 15 V, or a contact switch. Positive or negative logic selectable.
Output current monitor *1
Monitor voltage range selectable: 0 V to 5 V or 0 V to 10 V, Accuracy: 1%
Output voltage monitor
Monitor voltage range selectable: 0 V to 5 V or 0 V to 10 V, Accuracy: 1%
Normal operation status signal
Normal (4 V to 5 V), abnormal (0 V), output resistance 500 Ω
Parallel operation *2 *3
Possible up to six power supplies. Master-slave operation with a current balance function.
Series operation *4
Possible up to two power supplies.
Constant voltage/constant current mode (CV/CC) signal
Open collector output (maximum application voltage 30 V, maximum sink current 10 mA)
Low level (on) during constant current (CC) mode High level (off) during constant voltage (CV) mode
Output on / off control (ILC)
Output can be shut off using a contact switch or the like (maximum voltage between terminals: 5 V). When open: Output off When shorted: Output on
Local / remote
Can be switched by applying an external voltage or by opening or shorting the circuit.
Local: 2 V to 15 V or open Remote: 0 V to 0.6 V or shorted
External control status signal
Open collector output (maximum application voltage 30 V, maximum sink current 10 mA)
High level (off) during local mode Low level (on) during external control
Trigger output signal
Maximum low level output signal: 0.8 V
Minimum high level output signal: 3.8 V, maximum high level output signal: 5 V
Maximum source current: 16 mA, output trigger signal span: 20 μs (typ)
Trigger input signal
Maximum low level input signal: 1.2V
Minimum high level input signal: 3.5 V, maximum high level input signal: 5 V
Maximum sink current: 16 mA, positive edge trigger span: 10 μs (min)
Tr/Tf: 1 μs (max)
Program signal output 1
Open collector output (maximum application voltage 25 V, maximum sink current 100 mA)
Program signal output 2
*1. In output current control, the current, linearity, and monitor accuracies do not include the load variation caused by initial drift and temperature drift of internal components. *2. For parallel operation of two or more PAV series power supplies with the same rating, the minimum load current is 5% of the rating or higher. For parallel operation of four or less models with rated output voltage of 160 V to 650 V, the minimum load current is 5% of the rating or higher. For parallel operation of more than four, the minimum load current is 20% of the rating or higher. *3. The ammeter’s display accuracy when the total current is displayed on the master unit is 2% ± 1 count of the total of rated currents. *4. An external protection diode is necessary.
0 °C to 50 °C (32 °F to 122 °F) 20%rh to 90%rh (no condensation)
Storage ambient temperature and humidity
-20 °C to 85 °C (-4 °F to 185 °F) 10%rh to 95%rh (no condensation)
Installation location
Indoors, overvoltage category II
Altitude: Up to 3000 m (at 2000 m and above, the operating ambient temperature must be reduced), At 2000 m to 3000 m, the operating ambient temperature is 0 °C to 40 °C (32 °F to 104 °F).
Operating ambient temperature and humidity
0 °C to 50 °C (32 °F to 122 °F) 20%rh to 90%rh (no condensation)
Storage ambient temperature and humidity
-20 °C to 85 °C (-4 °F to 185 °F) 10%rh to 95%rh (no condensation)
Installation location
Indoors, overvoltage category II
Altitude: Up to 3000 m (at 2000 m and above, the operating ambient temperature must be reduced), At 2000 m to 3000 m, the operating ambient temperature is 0 °C to 40 °C (32 °F to 104 °F).
1.9 kg (4.2 lb) or less: 200 W, 400 W types (models whose rated output voltage is 10 V to 100 V and 160 V to 650 V)
2.0 kg (4.4 lb) or less: 600 W, 800 W types (models whose rated output voltage is 160 V to 650 V)
2.1 kg (4.6 lb) or less: 600 W, 800 W types (models whose rated output voltage is 10 V to 100 V)
Dimensions
See outline drawing.
Vibration resistance
IEC60068-2-64
Shock resistance
196.1 m/s2 (20 G) or less, half sine, 11 ms, when not packaged, when not operating (IEC 60068-2-27)
Cooling system
Forced air cooling using internal fan
Weight
1.9 kg (4.2 lb) or less: 200 W, 400 W types (models whose rated output voltage is 10 V to 100 V and 160 V to 650 V)
2.0 kg (4.4 lb) or less: 600 W, 800 W types (models whose rated output voltage is 160 V to 650 V)
2.1 kg (4.6 lb) or less: 600 W, 800 W types (models whose rated output voltage is 10 V to 100 V)
Dimensions
See outline drawing.
Vibration resistance
IEC60068-2-64
Shock resistance
196.1 m/s2 (20 G) or less, half sine, 11 ms, when not packaged, when not operating (IEC 60068-2-27)
Conforms to the requirements of the directive and standard below.
Low Voltage Directive 2014/35/EU *2
UL/EN/IEC 61010-1 (Class I *1, Pollution degree 2 *2) (Design to meet UL/EN 60950-1) ● Models whose rated output voltage is 10 V, 20 V, 36 V, or 60 V
Output terminals and signal terminals produce non-hazardous voltage. ● Models whose rated output voltage is 100 V, 160 V, 320 V, or 650 V
Output terminals and J1 and J2 terminals produce hazardous voltage (other signal terminals produce non-hazardous voltage).
EMC
Conforms to the requirements of the directive and standard below.
EMC Directive 2014/30/EU
EN/IEC 61326-1 (Design to meet EN 55022/EN 55024)
Withstanding voltage *3
● Models whose rated output voltage is 10 V, 20 V, or 36 V
4242 Vdc: Between input and output (including between signal terminals)
2828 Vdc: Between input and FG
707 Vdc: Between output (including between signal terminals) and FG
● Models whose rated output voltage is 60 V or 100 V
4242 Vdc: Between input and output (including between signal terminals)
2828 Vdc: Between input and FG
707 Vdc: Between signal terminals (excluding J1/J2) and FG
1910 Vdc: Between output as well as J1/J2 terminals and signal terminals (excluding J1/J2)
1380 Vdc: Between output as well as J1/J2 terminals and FG
● Models whose rated output voltage is 160 V or 320 V
2970 Vdc: Between input and output (including between signal terminals)
2828 Vdc: Between input and FG
707 Vdc: Between signal terminals (excluding J1/J2) and FG
4242 Vdc: Between input and signal terminals (excluding J1/J2)
3200 Vdc: Between output as well as J1/J2 terminals and signal terminals (excluding J1/J2)
2000 Vdc: Between output as well as J1/J2 terminals and FG
● Models whose rated output voltage is 650 V
3704 Vdc: Between input and output (including between signal terminals)
2828 Vdc: Between input and FG
707 Vdc: Between signal terminals (excluding J1/J2) and FG
4242 Vdc: Between input and signal terminals (excluding J1/J2)
4244 Vdc: Between output as well as J1/J2 terminals and signal terminals (excluding J1/J2)
2780 Vdc: Between output as well as J1/J2 terminals and FG
Insulation resistance
100 MΩ or higher (25 °C, 70%rh)
Conducted emission
IEC/EN 61326-1, Class B, FCC part15-B, VCCI-B
Radiated emission
IEC/EN 61326-1, Class A *4, FCC part15-A, VCCI-A
*1. This is a Class I equipment. Be sure to ground the product’s protective conductor terminal. The safety of this product is only guaranteed when the product is properly grounded. *2. Pollution is addition of foreign matter (solid, liquid or gaseous) that may produce a reduction of dielectric strength or surface resistivity. Pollution Degree 2 assumes that only non-conductive pollution will occur except for an occasional temporary conductivity caused by condensation. *3. Test voltage application time: 1 minute *4. This is a Class A equipment. The product is intended for use in an industrial environment. This product may cause interference if used in residential areas. Such use must be avoided unless the user takes special measures to reduce electromagnetic emissions to prevent interference to the reception of radio and television broadcasts.
Safety
Conforms to the requirements of the directive and standard below.
Low Voltage Directive 2014/35/EU *2
UL/EN/IEC 61010-1 (Class I *1, Pollution degree 2 *2) (Design to meet UL/EN 60950-1) ● Models whose rated output voltage is 10 V, 20 V, 36 V, or 60 V
Output terminals and signal terminals produce non-hazardous voltage. ● Models whose rated output voltage is 100 V, 160 V, 320 V, or 650 V
Output terminals and J1 and J2 terminals produce hazardous voltage (other signal terminals produce non-hazardous voltage).
EMC
Conforms to the requirements of the directive and standard below.
EMC Directive 2014/30/EU
EN/IEC 61326-1 (Design to meet EN 55022/EN 55024)
Withstanding voltage *3
● Models whose rated output voltage is 10 V, 20 V, or 36 V
4242 Vdc: Between input and output (including between signal terminals)
2828 Vdc: Between input and FG
707 Vdc: Between output (including between signal terminals) and FG
● Models whose rated output voltage is 60 V or 100 V
4242 Vdc: Between input and output (including between signal terminals)
2828 Vdc: Between input and FG
707 Vdc: Between signal terminals (excluding J1/J2) and FG
1910 Vdc: Between output as well as J1/J2 terminals and signal terminals (excluding J1/J2)
1380 Vdc: Between output as well as J1/J2 terminals and FG
● Models whose rated output voltage is 160 V or 320 V
2970 Vdc: Between input and output (including between signal terminals)
2828 Vdc: Between input and FG
707 Vdc: Between signal terminals (excluding J1/J2) and FG
4242 Vdc: Between input and signal terminals (excluding J1/J2)
3200 Vdc: Between output as well as J1/J2 terminals and signal terminals (excluding J1/J2)
2000 Vdc: Between output as well as J1/J2 terminals and FG
● Models whose rated output voltage is 650 V
3704 Vdc: Between input and output (including between signal terminals)
2828 Vdc: Between input and FG
707 Vdc: Between signal terminals (excluding J1/J2) and FG
4242 Vdc: Between input and signal terminals (excluding J1/J2)
4244 Vdc: Between output as well as J1/J2 terminals and signal terminals (excluding J1/J2)
2780 Vdc: Between output as well as J1/J2 terminals and FG
Insulation resistance
100 MΩ or higher (25 °C, 70%rh)
Conducted emission
IEC/EN 61326-1, Class B, FCC part15-B, VCCI-B
Radiated emission
IEC/EN 61326-1, Class A *4, FCC part15-A, VCCI-A
*1. This is a Class I equipment. Be sure to ground the product’s protective conductor terminal. The safety of this product is only guaranteed when the product is properly grounded. *2. Pollution is addition of foreign matter (solid, liquid or gaseous) that may produce a reduction of dielectric strength or surface resistivity. Pollution Degree 2 assumes that only non-conductive pollution will occur except for an occasional temporary conductivity caused by condensation. *3. Test voltage application time: 1 minute *4. This is a Class A equipment. The product is intended for use in an industrial environment. This product may cause interference if used in residential areas. Such use must be avoided unless the user takes special measures to reduce electromagnetic emissions to prevent interference to the reception of radio and television broadcasts.
Cookies will be used to track which website is being visited. On our website, we certify the information that can be accessed by visitors using cookies. We also track viewed information by users to understand your interest and provide you with a better content. You will be able to disable cookie itself, you may choose the way to use personal identification whenever you use service that requires authentication.
Strictly Necessary Cookies
Strictly Necessary Cookie should be enabled at all times so that we can save your preferences for cookie settings.
If you disable this cookie, we will not be able to save your preferences. This means that every time you visit this website you will need to enable or disable cookies again.
Additional Cookies
This website uses the following additional cookies:
(List the cookies that you are using on the website here.)
Please enable Strictly Necessary Cookies first so that we can save your preferences!