Total length 2.5m, AC cable for PWX750ML (Rated voltage 250V / Rated current 10A)

Total length 2.5m, AC cable for PWX750ML (Rated voltage 250V / Rated current 10A)

Total length 3m, AC cable for PWX750ML (rated voltage 120V/rated current 15A)

3-core cabtyre cable3m 8sq M5 for SR

Conversion cable for RS-232C controlD-sub 9P - RJ45, total length: 2m

Sensing cable set for OP03-PFX (CE compliant) Test lead for 8-point cell voltage measurement Total cable length 3 m Maximum operating temperature: 105°C Sample side tip cut-off The CE marked products PFX2512 / 2532

Compatible with PXB20K-50Length : 3mMaximum allowable current：800ATerminal size：M12/M12

For PCR18000WEA2R (three-phase 3-wire 400 V input)

For PCR24000WEA2R (three-phase 3-wire 400 V input)

Three-phase input power cordLength : 3mNominal cross-sectional area : 22mm2Terminal size：M6

Load cable Length : 3m Maximum allowable current : 200A Terminal size：M10/M10

Parallel operation signal cable

Parallel operation cable for SPEC71200

AC Cable for SPEC71200

Output cable (with connector): AWG10(equivalent to 5.5 mm2), cable length: approx. 5 m Voltage sensing cable (with connector): AWG24, cable length: approx. 5 m Thermocouple: AWG24, T type, Teflon, wire diameter: 0.32 mm2, cable length: approx. 5 m Cable ties: 10 pcs.

Output cable (with connector): AWG10(equivalent to 5.5 mm2), cable length: approx. 2 m Voltage sensing cable (with connector): AWG24, cable length: approx. 2 m Thermocouple: AWG24, T type, Teflon, wire diameter: 0.32 mm2, cable length: approx. 3 m Cable ties: 4 pcs.

Load cables for high voltages up to 80 A (our recommended current). Length: 3 m, Max: 2000 V/ 80 A, Thickness: 22 mm2

Sensing cable set (for OP03-PFX) Test lead for 8-point cell voltage measurement Total cable length 5m Maximum operating temperature: 105°C Sample side tip cut-off PFX2512 / 2532

Lead wires for voltage and thermometer units for 4 cells K-Type Thermocouple Length: 5m

Accessory Kit for PLZ-4W/4WH series. Used for the connection of J1 Connector on the rear panel when operating by external control. Contents: Connector, Semi-cover, Pin(20 sets)

Accessory Kit for PLZ-4WL series. Used for the connection of J1 Connector on the rear panel when operating by external control. Contents: Connector, Semi-cover, Pin(26 sets)

Maximum working voltage: 150 V Maximum operating current: 1000 A Terminal: M12/M12 Nominal cross-sectional area: 600 mm2 Length ： 3m, Mass (per bottle) : Approx. 20 kg (20 lbs)*Prices are for a set of two (for positive and negative poles). (DC150-4P3M-M12M12 is a set of 4 (2 for positive...

Low inductance cable 50A Cable length: 2m Terminal: M6*Low inductance cables can be used only when the output is grounded. Cannot be used when not grounded. (In case of SR)

Low inductance cable 50A Cable length: 1m Terminal: M6*Low inductance cables can be used only when the output is grounded. Cannot be used when not grounded. (In case of SR)

3-core cabtyre cable 3m 14sq M5 for BP

Terminal block box that can be magnetically attached to PAS series main units, etc. Maximum Output rating: 30A (600V or less) Dimensions / Weight: approx. 124W x 34H x 100Dmm / 700g Cable length: approx. 60 cm Accessories: magnet, terminal protection cover

26-pin connectorSemi-coverPin x 10ground cable

A terminal unit for converting the J1 and J2 connectors of this product to the J1 connector of the Kikusui PWR Series Regulated DC Power Supplies. *Output voltage (current) external resistance control and one-control parallel operation (series operation) cannot be converted.

Connection cable for 30k and 36kVA (1.4m)

Connection cable for 30k and 36kVA (0.7m)

Connection cable for 24kVA (1.4m)

Connection cable for 24kVA (0.7m)

Connection cable for 18kVA (1.4m)

Connection cable for 18kVA (0.7m)

Connection cable for 6k and 12kVA (1.4m)

Connection cable for 6k and 12kVA (0.7m)